I use AI to analyze your logs as follows:   From the log information you provided, there are several key errors and warnings to note: F2FS not supported on PAGE_SIZE(16384) != 4096:This...

This article breaks down how to boot a Raspberry Pi 4 from an SSD using the X825 and X735 boards. If you’re diving into Pi upgrades and want faster, more reliable boot times, this guide is go...

PiOS/Debian 12.7 Linux rpi3 6.6.31+rpt-rpi-2712 #1 SMP PREEMPT Debian 1:6.6.31-1+rpt1 (2024-05-29) aarch64 GNU/Linux After setting up an identical system, I'm beginning to wonder if maybe it's ju...

PiOS 12.6 to 12.7 What version is this? My current version are as follows: pi@raspberrypi:~ $ uname -a Linux raspberrypi 6.6.47+rpt-rpi-v8 #1 SMP PREEMPT Debian 1:6.6.47-1+rpt1 (2024-09-02) a...

Follow up: I wrote a script to check voltage every second and then log every minute the results for that cycle including minimum voltage, max voltage and average voltage over the 60 seconds along ...

I've been using an X1012 PoE + NVMe board for a few months now, and it has been very stable until this past week.  I updated from PiOS 12.6 to 12.7, and now it seems that my drive "disappears...

Thanks for the response.  I want to clarify what I saw (and still see although less often). When I first posted my Pi was on my desktop as I was reconfiguring it so it was only conected to a ...

We do not recommend using VGA to HDMI or DP to HDMI wire to provide HDMI signals to the X650, especially VGA to HDMI wire, which will result in no signal.

Ok final update. I guess the HDMI on my card is the only thing wrong (at the moment). For anyone who wants to know, its a "Zotac Gaming GeForce GTX 1660 OC". I had an extra DP to HDMI and its curre...

Scratch all of that. After testing yet again, it looks like the HDMI port on the video card has gone out and was going out, JOY!!! I plugged in my retro scaler and it gave me a signal on the x650. ...

So reflashed and flashed an older version. Both do not work and keep getting no signal. HDMI checks fine with a monitor so I have now idea whats going on other than a possible hardware issue with t...

It was purchased via Amazon (Link to item). I don't think its a flash issue and I have tried a couple of different V3 images that all do the same, no signal. I'll try another full download/flash an...

Since X650 V1.5, we have used the same pcf8563 RTC chip with PiKVM official hardware, so you don't need to do anything, the RTC will work fine. I don't know where you purchased our product fro...

Sorry for the late reply. Today, we tested X1203 and the results are as follows: 1: This is a full picture of the test. Please excuse my messy desktop.   2. There is no power supply to ...

The x650 is prefect for my needs but having issues with. First, I cannot get this to thing to work with any video at all. I have tried just about everything but use a custom EDID. Running dmesg | ...

I was thinking more a way the Pi measures the voltage source and, since it is not coming through the USBC connector, the measurement is not valid - but this is just wishfull thinking I admit. ...

I'll have to check the pogo pins on mine.  A very possible cause.

I switched out the approved power supply for an 18v 6a to try this and  I still get some (although I don't think as many) low voltage warnings.  I've sent a direct support message to Geek...

Same problem.  12.2 volts to the UPS  and same low voltage warning Pi5

@coreball It sounds like the power draw from charging and running the Pi + SATA HAT is overwhelming the board. You might need to limit charging current, reduce disk access during charging, or upgra...