hello
All Posts
-
2 / 4 Pin Connectors
Hello, I am curious where I might be able to source the 2 or 4 wire pigtails that plug into the 5v in/out and momentary switch on the x735.
-
Third Generation HDMI to LVDS board. What has changed?
@monkey mart This update has solved some compatibility problems.
-
12v Power Loss Solution?
Thank you for your quick reply. I am using a Pi 4 and found the x735 while looking to replace Mausberry Circuit's 4amp Car Supply / Switch. It failed on me and I believe many others and is not avai...
-
12v Power Loss Solution?
I saw that you bought X729, so I guess you are using it on RPi 4. Since X728 only supports DC 5V, you bought X729 which can support 12V input, which is correct. Thank you for your support.
-
12v Power Loss Solution?
Hello X735 definitely does not support the power failure detection and safe shutdown you mentioned, because X735 is not a UPS shield. It will stop working immediately after the power failure. You ...
-
12v Power Loss Solution?
I recently purchased a x735 because I was under the impression that it could detect power loss and initiate a safe shutdown. After installing it I have noticed this is not the case. Now I am trying...
-
x1201 won't Auto-On after shutdown from bat.py script
I'm using the bat.py script to shutdown the Pi5 as soon as power is lost, rather than waiting for the depletion of the battries, but when power is restored, it will not turn the Pi back on. I...
-
X1200 UPS not detected on Raspberry Pi 5 i2c
I already checked connections 4 times by disassembling it. I cleared the connections with rubber, even though they are very clean because my Pi is only one year old. I also sent logs confirming ic2...
-
X1200 UPS not detected on Raspberry Pi 5 i2c
Hello 1. Make sure you enable i2c interface, refer to How to enable I2C 2. The UPS connects to the Pi GPIO via pogo pins, If the I2C address (0x36) is not detected, Please clear the ...
-
X1200 UPS not detected on Raspberry Pi 5 i2c
After installing fresh new X1200 UPS I can't get any status code from i2cdetect: i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- ...
-
UPS X1201 X1202 - Batteries voltage balancing
Hi AllRecently got a X1201 and X1202, before installing the batteries to the UPS, do i have balance all batteries to be same voltages before installing to the UPS ? Will the UPS manage e...
-
Is X728 board compatible with X825 and metal case C6?
Great setup, Pierre! You're right—the X728 is the better choice for safe shutdowns and battery backup. I’ve been through a similar situation while running Space Waves sessions on my Pi&...
-
-
Just have got the pikvm-a8
It sounds like you're having trouble with your X630 HDMI to CSI-2 capture device. The red LED and the fact that the video isn't being detected suggest a problem with the device itself. Since the pa...
-
Just have got the pikvm-a8
@Sprunki Retake I also encountered the same problem with the X630 HDMI to CSI-2 device—the red light was always on and no video was received, even though I followed the video instructions exa...
-
Half height X650 PCIe doesn't fit in slot in server
I actually ran into a similar issue a while back with a Dell R640 server and a network card. Even though the card was advertised as half height, the bracket was just a bit off and wouldn’t se...
-
X873 V1.2 M.2 NVME SSD Expansion Board for Raspberry Pi 4 Model B
I am also looking for similar ideas @Survival race
-
Pi5 X1001 Shield and Aliminium Case
Great to hear about your positive experience with the Pi5 X1001 Shield and aluminum case! It sounds like a perfect upgrade! @Traffic Rally
-
HDD LED in web interface stuck being red shortly after boot
No one has any idea? How do I get the attention of Geekworm themselves?