@michael matyas i also have no function from a kingspec NX 2230 512GB NVME M.2 

Realized a unified diff might be a bit nicer... ;) --- /usr/bin/kvmd-oled.orig 2023-08-26 07:02:20.000000000 +0300 +++ /usr/bin/kvmd-oled 2024-01-01 03:45:02.217732020 +0300 @@ -21,6 +21,7 @@ ...

Peter, you didn't say, but the below assumes you are using an RPi4b. With the 4b, you only really have two choices as to which set of PWM outputs to use; GPIO 12&13 or  GPIO 18&19 (pi...

@Maurizio Imperatrice this didn't work for me.  lsblck shows nothing with a "KingSpec 512GB 2230 SSD NVMe Gen3x4, M.2 PCIe 3.0 SSD with 3D NAND Flash"

@Sijmen Visser how the heck do you figure ut what  controller an nvme m.2 drive has??  geekwork doesn't bother telling us how to know this.  yet they say their device has a defect th...

@michael matyas I couldn't get the X1000 to recognize the SSD, so I opened a case with Geekworm and they eventually sent me a new (ver 1.5) X1000 board.  This is the one with the single LED th...

@cragen Loch Today I had the time to try out your suggestions. I used your suggested https://www.tindie.com/products/jeremycook/ez-fan2-tiny-raspberry-pi-fan-controller/ When using the default GP...

X735 Power management board+ X862 + X857-C3    survivor io X708 UPS + X862 + X857-C3 I got it. Thanks for your sharing.

The NASPi version that is now available does not allow the function of automatically turning on the device; however, the AUTO ON function will be included in the subsequent version.  You can c...

You can check out to https://geekworm.com/community/forum/topic/121718/creations-with-acrylic-powders survivor io learn more 

@Mitchell Winters <a href="https://google.com/" rel="dofollow">google</a>

Could you perhaps try formatting the solid-state drive (SSD) so that we may test it once more? https://wiki.geekworm.com/File:Tutorial_Initalize_New_SSD.pdf google

I think X708 ups are not compatible with X750 ups in any way.  

dmesg log also has such messages on each attempt to read from ssd: "nvme I/O 960 (I/O Cmd) QID 3 timeout, aborting"

Hi! I've installed X1002 with NVMe (non-Phison chipset). Then I booted to linux OS and put dtparam=pciex1 to config.txt - it let the SSD drive to become visible. But it operates VERY slow! It makes...

I found my problem. My SSD has Phison controller. As noted in https://geekworm.com/products/x1001 it's not compitable. 

Update:Imaged an USB drive.  Without the SSD plugged into the Pi it boots fine with the USB drive. With the SSD inserted in the hat it won't start (green light, full fans & no HDMI output)...

I tried all suggestions above, but my Pi5 won't boot with the X1001 hat. The blue light is on, but nothing happens (Pi5 light is green, screen show no signal and fans are noisy). The Pi5 also does ...

@Ivan Podogov If your DOS partition was obtained by flashing the Raspberry Pi OS, it should be fine, but many users are using OLD SSDs, which will have old OS on them, such as windows 10 or other O...

We've found customer feedback that they don't recognize SSDs, the firmware & configuration are fine, and there's no problem with the power supply. But just not recognized. The final solution i...