Hi,Please attach your order and email us, we can help you via email.1. Please provide the order number.2. Please provide the hardware connection photos, the SSD model you use.3. Make sure the FFC c...
All Posts
-
-
Geekworm X1001 is not working
Rachel Fleming posted in General Discussion •Hello, I am missing something. /boot/config.txt is set with dtparam=audio=on,pciex1. I tried the "nvme" param as well. dmesg | grep nvme founds nothing. lspci have a broadcom bridge and and Eth co...
-
Geekworm KVM-A8 / PiKVM question
gloriasenter934 posted in General Discussion •I was wondering if anyone knows as to whether or not these devices can schedule power on (not WoL) / off operations, I'm assuming they can purely because they pass through the front panel headers t...
-
X1012 - NVMe drive "disappears" after 12.7 upgrade?
Harry Huang posted in General Discussion •I use AI to analyze your logs as follows: From the log information you provided, there are several key errors and warnings to note: F2FS not supported on PAGE_SIZE(16384) != 4096:This...
-
Pi 4: Boot from SSD using X825 and X735
Winona Goodwin posted in General Discussion •This article breaks down how to boot a Raspberry Pi 4 from an SSD using the X825 and X735 boards. If you’re diving into Pi upgrades and want faster, more reliable boot times, this guide is go...
-
X1012 - NVMe drive "disappears" after 12.7 upgrade?
DigiK posted in General Discussion •PiOS/Debian 12.7 Linux rpi3 6.6.31+rpt-rpi-2712 #1 SMP PREEMPT Debian 1:6.6.31-1+rpt1 (2024-05-29) aarch64 GNU/Linux After setting up an identical system, I'm beginning to wonder if maybe it's ju...
-
X1012 - NVMe drive "disappears" after 12.7 upgrade?
Harry Huang posted in General Discussion •PiOS 12.6 to 12.7 What version is this? My current version are as follows: pi@raspberrypi:~ $ uname -a Linux raspberrypi 6.6.47+rpt-rpi-v8 #1 SMP PREEMPT Debian 1:6.6.47-1+rpt1 (2024-09-02) a...
-
X1203 UPS Voltage Drops
razmichael posted in General Discussion •Follow up: I wrote a script to check voltage every second and then log every minute the results for that cycle including minimum voltage, max voltage and average voltage over the 60 seconds along ...
-
X1012 - NVMe drive "disappears" after 12.7 upgrade?
DigiK posted in General Discussion •I've been using an X1012 PoE + NVMe board for a few months now, and it has been very stable until this past week. I updated from PiOS 12.6 to 12.7, and now it seems that my drive "disappears...
-
X1203 UPS Voltage Drops
razmichael posted in General Discussion •Thanks for the response. I want to clarify what I saw (and still see although less often). When I first posted my Pi was on my desktop as I was reconfiguring it so it was only conected to a ...
-
X1203 UPS Voltage Drops
Harry Huang posted in General Discussion •Sorry for the late reply. Today, we tested X1203 and the results are as follows: 1: This is a full picture of the test. Please excuse my messy desktop. 2. There is no power supply to ...
-
X1203 UPS Voltage Drops
razmichael posted in General Discussion •I was thinking more a way the Pi measures the voltage source and, since it is not coming through the USBC connector, the measurement is not valid - but this is just wishfull thinking I admit. ...
-
X1203 UPS Voltage Drops
Douglas Wyman posted in General Discussion •I'll have to check the pogo pins on mine. A very possible cause.
-
X1203 UPS Voltage Drops
razmichael posted in General Discussion •I switched out the approved power supply for an 18v 6a to try this and I still get some (although I don't think as many) low voltage warnings. I've sent a direct support message to Geek...
-
X1203 UPS Voltage Drops
Douglas Wyman posted in General Discussion •Same problem. 12.2 volts to the UPS and same low voltage warning Pi5
-
X1203 UPS Voltage Drops
razmichael posted in General Discussion •X1203 with two x 2 battery packs on Pi5. I'm seeing voltage drops to the Pi under various loads that will drop to 4.9 or so and often trigger the Pi Low Voltage threshold warning. ...
-
X1300 Stream to Raspberry display
Harry Huang posted in General Discussion •@Alex Smart We have no experience in processing the HDMI source through TC358743 and then streaming it into another display. But it seems that you can use X1301 to see the current input source sig...
-
X1300 Stream to Raspberry display
Alex Smart posted in General Discussion •Im strarting with X1300 and wiki article was very useful, I managed to save a file from HDI input. However I want to stream HDMI input directly to Raspberry display (currently HDMI) and have no luc...
-
power connector x1009 v1.1
drew drew posted in General Discussion •I understand, but maybe the 12V input power connector is directly connected to the 12V power connector for powering the drives and it doesn't matter where the power is connected.These two connector...
-
power connector x1009 v1.1
Harry Huang posted in General Discussion •@drew drew No, it's 12v for OUT HDDs
