Was wondering if there is a portable power solution for the Raspberry pi 5 that doesen't interfere with gpio signal. I would like to use a screen like the pimoroni hyperpixel touch which uses all t...
All Posts
-
X301 SATA NAS Storage Expansion Board - UASP issue
tenox7 posted in General Discussion •Hi, I have https://geekworm.com/products/x301 attached to a RPI Zero 2W, with latest Raspbery PI OS. On the product page it says: Supports USB Attached SCSI Protocol (UASP) however when I lo...
-
X1202 not charging batteries
lindasmile116 posted in General Discussion •This is very likely a hardware issue in the battery path, not a software problem. Key signs: BATT_V = 0.003V → the PMIC does not see the battery at all, even though each cell measures ~4...
-
-
Active Cooler H505 strange temperature fluctuation
florin.andrei posted in General Discussion •I think I've found the answer. If you read /boot/firmware/overlays/README you will see this: ``` fan_temp0 Temperature t...
-
Active Cooler H505 strange temperature fluctuation
florin.andrei posted in General Discussion •I bought a couple Active Cooler H505 blowers for Raspberry Pi 5, and they work well. There is one curious detail that I cannot explain. I have Prometheus recording the vital stats of several syste...
-
Don't recognize / boot from NVME SSD for X1001/X1002/X1000/X1003?
now.abhi posted in General Discussion •tried your commands but it does not work in my case !
-
Geekworm X1004 Dual M.2 2280 NVMe HAT no nvme getting detected.
now.abhi posted in General Discussion •hello. i have rpi5 16b model and have newly bought Geekworm X1004 Dual M.2 2280 NVMe HAT from robu.in and i have 2 nvme 1 tb crucial p3 plus and second nvme 2 tb p3 crucial plus nvme both wo...
-
C790 Latency
electricnguyen09 posted in Pre-Sales Questions •Hello! However, this can increase if: The host/driver introduces buffering or frame-synchronization delays. Edit by: Drift Boss last 1 day ago!
-
-
X825 + X735 + metal case + RPi4 - auto power ON
limecharlie60 posted in General Discussion •If I understand correctly: you want to auto-on when power is supplied, and use a button to turn it on/off — in my opinion you can: turn on auto-on, and use a momentary switch to shutdown. But...
-
C790 Latency
duncanmclaud61 posted in Pre-Sales Questions •I tried poki free games and the experience felt lighter than I expected. The site loads quickly the games start instantly and the whole rhythm stays calm which makes it easy to play during short br...
-
Issues with installation of X-C1 fan software.
minaches posted in General Discussion •I want to use these upgrades to develop gaming software, it seems to be optimized for use
-
Modify PiKVM for Raspberry pi 5 (with KVM-A8)
sebastian posted in General Discussion •I have a KVM-A8. I have successfully modified the hardware so it runs on rpi 5 (replaced the CSI cable with a rpi5 camera cable, as the HDMI capture card emulates a camera) AND (replaced the fan wi...
-
X1202 not charging batteries
DR posted in General Discussion •Hi, My X1202 stopped charging the batteries. The battery indicator is always 4 bars on the LED. I checked the batteries invidually using a multimeter and they all have 4+ V, however battery volata...
-
X651 - does not boot
waking.end_2u posted in General Discussion •I've just installed the X651 with CM4002000 and flashed the image- the problem is, the raspberry receives an ip address but I cannot ping it or see the web interface. The leds on the board s...
-
LVDS to HDMI for 4K Panel
izzbo posted in Pre-Sales Questions •Hi everyone, I have a project that uses a BOE MV315QUM-N20 32" 60HZ 4k panel. My end goal is to be able to switch between a LVDS source and a HDMI source and display the selected input to the pane...
-
X1004 not recognized on RPi5
dacarson posted in General Discussion •Found the issue - Ribbon wire was faulty. Changed that, and it is now working.
-
X1004 not recognized on RPi5
dacarson posted in General Discussion •Hi, I was excited to recently get a X1004 to experiment with. I already had NVMe and PoE+ for RPi5 from HackerGadgets that I have been successfully using with a Coral Edge TPU (similar to hailo-8)...



