Hi, I managed to set the format to 1920x1080@50 however when I try to capture there's an error occur which tells me select timeout.
All Posts
-
X1301 unable to configure 1920x1080 format
Harry Huang posted in General Discussion •Please set the HDMI signal source to 1920@1080P and try again. I just tested it again, using my laptop as the hdmi signal source. Once I set the resolution of the laptop to 2880@1800, the output r...
-
X1301 unable to configure 1920x1080 format
zenkai_wong posted in General Discussion •Even if I changed to the 1080P50EDID the format still seems to stuck at 1280x720, after I rebooted both the source device and the device mounted with X1301.
-
X1301 unable to configure 1920x1080 format
Harry Huang posted in General Discussion •RPi 4 does not support 60HZ, you need to use the correct EDID
-
X1301 unable to configure 1920x1080 format
zenkai_wong posted in General Discussion •X1300 Software - Geekworm WikiI am using raspbian bookworm on Pi 4BI followed the steps from the software guide but there's an error when I tried to configure the dv timings therefore I am unable t...
-
x1009 low power
pasha1346798213 posted in General Discussion •Here voltages from terminal (Voltmeter says there are 5.05v and 3.33v)
-
x1009 low power
pasha1346798213 posted in General Discussion •Setup: Raspberry pi 5 8gb x1009 hat Usb ssd with OS 12v 10a PSU Ive connected gpio pins and pcie ffc On system boot appears low power alert which shutdown whole setup Try to ed...
-
Manipulating SATA commands directly with X1009
bhavyemathur posted in Pre-Sales Questions •Hey, We would like to build a device which acts as a middle-man to a harddrive. This involves reading SATA commands from a host computer, performing some logic on the commands, and sending...
-
Cooling options for geekworm X630-A8
chepe263 posted in General Discussion •@Cindy Ding what about a quieter fan?
-
Cooling options for geekworm X630-A8
Cindy Ding posted in General Discussion •Hi, You can refer to the last FAQ on the KVM-A8 WiKi: https://wiki.geekworm.com/KVM-A8#FAQ Q. Does KVM-A8 support passive heatsink such as (P165-A or P165-B etc) instead of fan? ...
-
Geekworm KVM-A8 / PiKVM question
choosechess57 posted in General Discussion •Yes, many devices with front panel headers, like those passing through to a Raspberry Pi, can schedule power on/off operations, though it depends on the specific model. You can check the device's m...
-
Cooling options for geekworm X630-A8
chepe263 posted in General Discussion •I recently acquired a geekworkm KVM-A8, the pci version, and it works great. PiKVM is really awesome. My only complain is the tiny fan inside. It has a tiny whine sound really noticiable at night....
-
Don't recognize / boot from NVME SSD for X1001/X1002/X1000/X1003?
bonitacaily0011 posted in General Discussion •Thank you for providing very useful information!
-
Don't recognize / boot from NVME SSD for X1001/X1002/X1000/X1003?
bonitacaily0011 posted in General Discussion •@Maurizio Imperatrice Thank you very much for this useful article!
-
Audio Setup for Remote Meetings with KVM-A3
gmena730 posted in General Discussion •Hi, I recently purchased the Geekworm KVM-A3 for use with PiKVM and I need some guidance on the audio setup for my specific use case: Setup:- Local laptop (source) → KVM-A3 + Raspberry Pi 4 &...
-
Neo 5 M.2 NVME case with Hailo 8L accelerator
jack.houben posted in Pre-Sales Questions •Does the Raspberry Pi Hailo 8L accelerator (PCIe) fit the Argon Neo 5 M.2 NVMe case?I just want to know if the PCIe module fits within the case. Thanks,Jack
-
Appears and disappears X1001
Harry Huang posted in General Discussion •Replied to your email, please check your email
-
Appears and disappears X1001
David Reid posted in General Discussion •I purchaed the X1001 and the 1TB Colorful NVME drive. Installed them. I get the blue light and the drive seems to be sensed by the computer. GPARTED sees the drive and can create and format ...
-
Redfish Power Managment with X680
craig.yamato posted in General Discussion •How can we get/set the system ID for each server connected to an X680 to control the ATX power using Redfish? It should be at the API endpoint "/redfish/v1/Systems/<Node ID>" but only a...
-
audio passthrough not working
clmetal posted in General Discussion •It was working, now I don't have the option to change my output device from computer speakers to the HDMI plugged into my device. It's not the computer; if I put the HDMI into a TV, it then g...
