Hello, It flat top 18650 batteries.
The PI ZERO 2W only supports USB 2.0, so it does not support the UASP protocol. However, the X301 hardware itself supports UASP. Please understand.
Harry Huang
Admin
Staff member
149
Posts
352
Profile views
10
Likes
0
Followers
Posts made by Harry Huang
-
UPS for Raspi 5 that doesen't use/require GPIO pinsposted in General Discussion
You should check if the Pimoroni Hyperpixel Touch is actually using GPIO 6 and GPIO 16.
-
Active Cooler H505 strange temperature fluctuationposted in General Discussion
Thanks for your sharing. 👍
-
x1202 Raspi does not switch back onposted in Pre-Sales Questions
Please note: If the UPS does not detect the RPi5, it will automatically shut down within 3 seconds. So you need to install the RPi 5 on the UPS and make sure that the RPi5 has good contact wit...
-
Geekworm X1202 UPS board with an NVMe base?posted in Pre-Sales Questions
@geekworm Sorry, X1202 does not support your idea.
-
Is it possible to adapt a x630-A4 to work with a full Rpi4 board?posted in Pre-Sales Questions
How would you like to assemble them?
-
12v Power Loss Solution?posted in Pre-Sales Questions
I saw that you bought X729, so I guess you are using it on RPi 4. Since X728 only supports DC 5V, you bought X729 which can support 12V input, which is correct. Thank you for your support.
-
12v Power Loss Solution?posted in Pre-Sales Questions
Hello X735 definitely does not support the power failure detection and safe shutdown you mentioned, because X735 is not a UPS shield. It will stop working immediately after the power failure. You ...
-
X1200 UPS not detected on Raspberry Pi 5 i2cposted in General Discussion
Hello 1. Make sure you enable i2c interface, refer to How to enable I2C 2. The UPS connects to the Pi GPIO via pogo pins, If the I2C address (0x36) is not detected, Please clear the ...
-
can i use a x1009 and 1 or 2 x-ups1posted in Pre-Sales Questions
You can stack multiple X-UPS1s to increase the current
-
Half height X650 PCIe doesn't fit in slot in serverposted in General Discussion
Very strange. Our half height bracket must be a standard part.
-
Geekworm Pi5 case - power switchposted in General Discussion
You can use the RPi5 power switch pad to bring out the switch yourself
-
Unable to Capture 1920x1080 Despite Supported Inputposted in General Discussion
@Wouter van de Pol Sorry for not replying to you due to the Chinese New Year holiday. Glad to see that you have solved the problem. Pikvm outputs edid to the target host for adjust...
-
X735 Power issueposted in General Discussion
@tzei57 Can you please send me a picture of your fully assembled unit? Or email us at support@geekworm.com.
-
X1301 unable to configure 1920x1080 formatposted in General Discussion
Please set the HDMI signal source to 1920@1080P and try again. I just tested it again, using my laptop as the hdmi signal source. Once I set the resolution of the laptop to 2880@1800, the output r...
-
X1301 unable to configure 1920x1080 formatposted in General Discussion
RPi 4 does not support 60HZ, you need to use the correct EDID
-
Appears and disappears X1001posted in General Discussion
Replied to your email， please check your email
-
X1012 - NVMe drive "disappears" after 12.7 upgrade?posted in General Discussion
I use AI to analyze your logs as follows: From the log information you provided, there are several key errors and warnings to note: F2FS not supported on PAGE_SIZE(16384) != 4096:This...
