@Harry Huang my board is not connected to any network. Do I need to disable Wi-Fi chip by some configuration? I replugged data cable mutiple times, rebooted board, tried different distros. I insta...

 In 4 stacks, is there RAID10 available.?

@loek dompeling  pi@raspberrypi:~ $ lsblkNAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINTSnvme0n1     259:0    0 465.8G  0 disk ├─nvme0n...

@Harry Huang  I use the X1002 shield and I discovered that without settings in boot.config, the Crucial SSD also boots.I do have the usual options enabled in the boot order.So it boots after ...

@Vitaly Chekryzhev Hi Only use pcie 2.0, DON'T open pcie 3.0. Try to close wifi then test? Thanks  

Feedback from other buyers: If the nvme is not recognised after adding dtparam=pciex1 to config.txt, add PCIE_PROBE=1 to the eeprom. That made my pi see the nvme. Run command: sudo rpi-eepro...

@etyrnal etyrnal Hello, Run the command: lspci Then check to see if the run result line contains the Phison   Thanks.

Rereading the manual pwm control commands, I see that I omitted the command to enable it once you have set the period. [root@pikvm pwm0]# echo 1 > enable  

@michael matyas i also have no function from a kingspec NX 2230 512GB NVME M.2 

Realized a unified diff might be a bit nicer... ;) --- /usr/bin/kvmd-oled.orig 2023-08-26 07:02:20.000000000 +0300 +++ /usr/bin/kvmd-oled 2024-01-01 03:45:02.217732020 +0300 @@ -21,6 +21,7 @@ ...

Peter, you didn't say, but the below assumes you are using an RPi4b. With the 4b, you only really have two choices as to which set of PWM outputs to use; GPIO 12&13 or  GPIO 18&19 (pi...

@Maurizio Imperatrice this didn't work for me.  lsblck shows nothing with a "KingSpec 512GB 2230 SSD NVMe Gen3x4, M.2 PCIe 3.0 SSD with 3D NAND Flash"

@Sijmen Visser how the heck do you figure ut what  controller an nvme m.2 drive has??  geekwork doesn't bother telling us how to know this.  yet they say their device has a defect th...

@michael matyas I couldn't get the X1000 to recognize the SSD, so I opened a case with Geekworm and they eventually sent me a new (ver 1.5) X1000 board.  This is the one with the single LED th...

@cragen Loch Today I had the time to try out your suggestions. I used your suggested https://www.tindie.com/products/jeremycook/ez-fan2-tiny-raspberry-pi-fan-controller/ When using the default GP...

X735 Power management board+ X862 + X857-C3    survivor io X708 UPS + X862 + X857-C3 I got it. Thanks for your sharing.

The NASPi version that is now available does not allow the function of automatically turning on the device; however, the AUTO ON function will be included in the subsequent version.  You can c...

You can check out to https://geekworm.com/community/forum/topic/121718/creations-with-acrylic-powders survivor io learn more 

@Mitchell Winters <a href="https://google.com/" rel="dofollow">google</a>

Could you perhaps try formatting the solid-state drive (SSD) so that we may test it once more? https://wiki.geekworm.com/File:Tutorial_Initalize_New_SSD.pdf google