I purchased the X728 ups hat to be used with a Pi 4. I am having issues with RTC. I'm running Ubuntu Server 20.04.   To rule out issues as my fault, here is what I did:  - in /b...

Hi Running:PRETTY_NAME="Raspbian GNU/Linux 10 (buster)" Fresh hardware install, following GUIDE from https://raspberrypiwiki.com/X728-Software Jumpers: PLD Step: 6 outputs: pi@raspberrypi:~ $ ...

I think I answered my own question in my OP, but I just realized while I was troubleshooting on my own, that the power supply I purchased is only 5V (actually indicates it can supply up to 8V on th...

I'm new to using geekworm products, but decided to try out an X832 (single 3.5" HDD board) with X735 (power management board) with a raspberry pi 4 (4GB model), inside of the geekworm case. I also ...

Hi, I have a Rpi 4 8G with an x708 UPS and X828 SDD/HDD boardes  attached and alos using a geekwork 5v 4a power supply and I'm seeing the below errors on the raspberry pi OS syslog, I'm conce...

@li xia but is it using some feature or concept unique to Raspberry Pi? According to description it is only setting up a link through USB 3.0, emulating standard USB drive, and the relationship wi...

As I can see, the only difference between Jetson Nano and RPi NAS HATs is the shape, sharing same electronics. And hardware need is only a functional USB3.x Port. Can I so suppose that appart of t...

Good morning. As per object I would like to know if it is possible to stack the raspberry pi 4 + x735 v2.1 + Raspberry Pi TV HAT. I would like to build an htpc that can be turned off comfortably wi...

@li xia That does not answer my question. The question is simple. Can you confirm whether or not I will be able to set up a 2 drive raid=1 array if my drieves are connected to my RPi4 through the X...

Well the title pretty much says it all. I am wondering if the X829 will support a two drive raid 1 array?

I'm pretty new to all of this but I want to make a NAS server for my family.  Ideally, what I want is for each person to have their own drive (5 in total) for their personal use (mainly to str...

Hi, Unless there is something else going on that I misunderstand, this is not my issue. I am having an issue with the batteries not staying charged even when plugged in with a more than capable po...

@li xia  That is what I expected the Blink Status to mean, However I wanted to verify. Thank you. As for the issue that I am seeing, I ran a few tests and have a bit of further information o...

Thanks for your time!

Also, and sorry for being so chaotic: what if I use a 10-pin cable to connect them?

@li xia Huh, OK, thanks for the reply. So a followup question would be: is there a dedicated case that might fit both the Jetson Nano and the T208?

I am seeing the CHG LED blink for a period of time, then it will stay constant for a few minutes and then start blinking again. This blinking feature does not appear to be documented anywhere and I...

Hi, The T208  UPS (https://geekworm.com/collections/nvidia/products/t208-18650-ups-max-5-1v-8a-output-power-management-expansion-board-for-nvidia-jetson-nano) looks awesome and I'm very much ...

Hi, The 2 extra 5v ports on the X835 I received don't seem to work. I wanted to add 2 25mm fans to the back of the x835 case, but the fans don't work when plugged into the ports. They show to be a...

Hello everyone, I'm trying to run 3 stepper motors using a raspberry pi 4 and two of "Geekworm's Raspberry Pi full function motor hat robot expansion boards". I recently found out that in order to...