Hello everyone, I'm trying to use the Geekworm X1001 with a Lexar NM610PRO NVMe drive. The Raspberry Pi's EEPROM is updated, I've set up NVMe booting, and I've flashed a new image onto the NVMe. Wh...

@Vitaly Chekryzhev We recommend avoiding the NVMe SSD drives which is equipped with a Phison controller due to their proven incompatibility. No problems were found except for the Phison controller.

if i set PCIe to gen 2, then lsblk doesn't show my nvme.  But if i set it to gen 3, then my lsblk shows my nvme

@etyrnal etyrnal when i had the kingspec, my X1003 would not even light up.  Now that i have a 512GB Inland pcie nvme m.2 gen 4x4, the X1003 lights up and recognizes the nvme...  i just c...

@Harry Huang With X1002 and Crucial T500 PCIe Gen 4 NVMe M.2 SSD 1TB, adding dtparam=pciex1_gen3 was the only solution that worked for me.

repeat speed test (Samsung 970 EVO PLUS 250GB NVMe)dd if=/dev/zero of=./TestingFile bs=100M count=10 oflag=directwrite speed = 727mb/s (with dtparam=pciex1_gen=3 in  sudo nano /boot/firmware/c...

Ivan is SD Copier in the "Lite" (No Desktop) image?? I forgot a step in my second post, after moving to the "Latest" eeprom, I also; raspi-config > 6. Advanced Options > A4 Boot Order > ...

I was using the default eeprom from Jan 5 2024 2/10/2024Today loaded "Latest" eeprom dated Jan 22 2024Now the x1001 blue light comes on when I power up the PI5 without the USB OS, but still does n...

X1001 not being mounted. I have the same OS on a USB and when it boots, the X1001 blue light comes on and the NVMe can be seen. Clone the usb to the NVMe and still will not boot (No blue light) fro...

My NVMe has SMI SM2263XT controller. Is it compatible with Pi and extension board?

@Harry Huang my board is not connected to any network. Do I need to disable Wi-Fi chip by some configuration? I replugged data cable mutiple times, rebooted board, tried different distros. I insta...

 In 4 stacks, is there RAID10 available.?

@loek dompeling  pi@raspberrypi:~ $ lsblkNAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINTSnvme0n1     259:0    0 465.8G  0 disk ├─nvme0n...

@Harry Huang  I use the X1002 shield and I discovered that without settings in boot.config, the Crucial SSD also boots.I do have the usual options enabled in the boot order.So it boots after ...

@Vitaly Chekryzhev Hi Only use pcie 2.0, DON'T open pcie 3.0. Try to close wifi then test? Thanks  

Feedback from other buyers: If the nvme is not recognised after adding dtparam=pciex1 to config.txt, add PCIE_PROBE=1 to the eeprom. That made my pi see the nvme. Run command: sudo rpi-eepro...

@etyrnal etyrnal Hello, Run the command: lspci Then check to see if the run result line contains the Phison   Thanks.

Rereading the manual pwm control commands, I see that I omitted the command to enable it once you have set the period. [root@pikvm pwm0]# echo 1 > enable  

@michael matyas i also have no function from a kingspec NX 2230 512GB NVME M.2 

Realized a unified diff might be a bit nicer... ;) --- /usr/bin/kvmd-oled.orig 2023-08-26 07:02:20.000000000 +0300 +++ /usr/bin/kvmd-oled 2024-01-01 03:45:02.217732020 +0300 @@ -21,6 +21,7 @@ ...