Update:   I removed the splash and quiet  from /boot/firmware/cmdline.txt.This provided me with the scrolling console logs.Then I changed the boot order and I was provided with the s...

Hi All,I'm failing to get my Rpi5 to boot from SSD with a NMVe SSD and the X1002 V1.1 hat.I have the Ediloca EN600 Pro SSD with 256GB and the X1002 Hat (V1.1), with a RPi5 with the latest Feb 5 202...

Hi guys, small update on my issue, maybe it could be helpful to someone else. I switched NVMe and moved to a Samsung 970 EVO Plus 1TB, and I've solved it. The Raspberry Pi 5 can finally boot from t...

@etyrnal etyrnal Hi, try to use the SD Card Copier to clone OS and select "New Partition UUIDS"  

Okay, sorry for the double post, but I just read that to understand if it's using a Phison controller, you have to use the command 'lspci'. From its output, there's no mention of 'Phison', so I bel...

Hello everyone, I'm trying to use the Geekworm X1001 with a Lexar NM610PRO NVMe drive. The Raspberry Pi's EEPROM is updated, I've set up NVMe booting, and I've flashed a new image onto the NVMe. Wh...

@Vitaly Chekryzhev We recommend avoiding the NVMe SSD drives which is equipped with a Phison controller due to their proven incompatibility. No problems were found except for the Phison controller.

if i set PCIe to gen 2, then lsblk doesn't show my nvme.  But if i set it to gen 3, then my lsblk shows my nvme

@etyrnal etyrnal when i had the kingspec, my X1003 would not even light up.  Now that i have a 512GB Inland pcie nvme m.2 gen 4x4, the X1003 lights up and recognizes the nvme...  i just c...

@Harry Huang With X1002 and Crucial T500 PCIe Gen 4 NVMe M.2 SSD 1TB, adding dtparam=pciex1_gen3 was the only solution that worked for me.

repeat speed test (Samsung 970 EVO PLUS 250GB NVMe)dd if=/dev/zero of=./TestingFile bs=100M count=10 oflag=directwrite speed = 727mb/s (with dtparam=pciex1_gen=3 in  sudo nano /boot/firmware/c...

Ivan is SD Copier in the "Lite" (No Desktop) image?? I forgot a step in my second post, after moving to the "Latest" eeprom, I also; raspi-config > 6. Advanced Options > A4 Boot Order > ...

I was using the default eeprom from Jan 5 2024 2/10/2024Today loaded "Latest" eeprom dated Jan 22 2024Now the x1001 blue light comes on when I power up the PI5 without the USB OS, but still does n...

X1001 not being mounted. I have the same OS on a USB and when it boots, the X1001 blue light comes on and the NVMe can be seen. Clone the usb to the NVMe and still will not boot (No blue light) fro...

My NVMe has SMI SM2263XT controller. Is it compatible with Pi and extension board?

@Harry Huang my board is not connected to any network. Do I need to disable Wi-Fi chip by some configuration? I replugged data cable mutiple times, rebooted board, tried different distros. I insta...

 In 4 stacks, is there RAID10 available.?

@loek dompeling  pi@raspberrypi:~ $ lsblkNAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINTSnvme0n1     259:0    0 465.8G  0 disk ├─nvme0n...

@Harry Huang  I use the X1002 shield and I discovered that without settings in boot.config, the Crucial SSD also boots.I do have the usual options enabled in the boot order.So it boots after ...

@Vitaly Chekryzhev Hi Only use pcie 2.0, DON'T open pcie 3.0. Try to close wifi then test? Thanks