@Harry Huang Thank you, I asked a friend using Pi4 with C790, the latency is much lower indeed. But I'm using the AI-Kit that only support Pi5. So I will try the X1300 or X1301 module later, maybe ...

My thoughts: pikvm os basically solves the latency problem. Pikvm os is an open source OS. I suggest you take a look at the source code of pikvm os. In addition, compared with Raspberry Pi 4, Ras...

I finally got the C790 working on the Pi5, but the live view latency is much higher than I expected.Here is my set up : I'm using Pi5, and did update and upgrade, C790 module is connected to t...

Hi all, I just purchased an NASPi Gemini 3.5 Dual 3.5' Kit with the X885 board, as well as the recomended Geekworm DC 5521 60W psu. I also have a Raspberry Pi 4 B+ 4gb. I've followed the setup ins...

Hello, you can refer to the following sample. #!/usr/bin/env python # import gpiod import time # Define the chip and lines chipname = "gpiochip0" #Please use gpiochip0 if using Raspberry...

Is the OLED displaying normally? If it is, you can ignore the hint.

Hi, Does anyone able to share how to write a callback event on falling edge on an Input GPIO. I can't find any example on how the lib handle event instead of using pulling method to find falling e...

Hi all I am facing problem in installing OLED. Here is one of the example: amps_pi5@raspberrypi:~/oled $ sudo pip3 install --upgrade setuptoolserror: externally-managed-environment × Thi...

Hi 1. The X680 does NOT support local video output, and the controlled computer can only be viewed through the PiKVM OS web UI. 2. You can connect a keyboard and mouse through the USB 2.0 port, w...

Hi, I wanted to confirm that it is expected that the local video output on the X680 4 port is for the CM4, but that the keyb and mouse are only KVM? It would have been good to have a keyb and mou...

@Richard Bolland  Hello Please use the new tutorial:  https://wiki.geekworm.com/X735-script

Hi I use an x735 with a Raspberry Pi4. After installing the software I find the x735pwr.sh uses almost 20% of the CPU. Extract from top:                &n...

@Jaime Nebrera  Hello Don't try to use X306 on the two boards you mentioned, because X306 uses pogo pins to power the Raspberry Pi zero 2w, and the pogo pins need to touch the welding pads o...

Hi all, Is the Geekworm X306 V1.3 18650 UPS Expansion Board compatible with those 2 boards? In particular with the E version with the POE hat? (Yes, in this case battery will not be charged by POE)

@Wouter van de Pol  Thank you for your extensive and patient testing. USB Drive: I tested using a USB drive connected to the Geekworm X680. For this point, consider my thoughts: The ...

@Harry Huang  I have tried multiple methods to boot from a mounted ISO using the Geekworm X680 IP KVM, but none have been successful. Here are the steps I've taken: ISO Files on CM4: I pla...

@Wouter van de Pol  Can you tell me more details about the ISO file processing? For example, where do you put your ISO file?There is another idea: you can put the OS installation file directl...

@Harry Huang  Thank you for the suggestion. I am aware of the link and have attempted all the steps mentioned multiple times without success. Could this be a hardware compatibility issue be...

@Wouter van de Pol  Maybe can refer to: https://github.com/pikvm/pikvm/issues/705

@Tomasz Kossakowski  Hello   I read your email and replied to you, I will reply here as well.   I discussed your problem with the engineer. There are several reasons:   ...