X728 Shutdown Options

• AR

  Aiden Ralph

  10/5/20, 9:15 PM

  Hi,  I have recently brought the X728 board for my raspberry Pi, and first of all I have to say it is brilliant!

  It's the only UPS I've tested that actually works correctly.

  I would however like some help with the shut down options.

  How can I change the script so that when you press the external button it shutsdown and powers off the pi and disconnects the battery with one press (and turns back on with one press)?

  I.e:

  

   

  It must be something to do with this script?

  #x728 Powering on /reboot /full shutdown through hardware
  #!/bin/bash

      sudo sed -e '/shutdown/ s/^#*/#/' -i /etc/rc.local

      echo '#!/bin/bash
  SHUTDOWN=5
  REBOOTPULSEMINIMUM=200
  REBOOTPULSEMAXIMUM=600
  echo "$SHUTDOWN" > /sys/class/gpio/export
  echo "in" > /sys/class/gpio/gpio$SHUTDOWN/direction
  BOOT=12
  echo "$BOOT" > /sys/class/gpio/export
  echo "out" > /sys/class/gpio/gpio$BOOT/direction
  echo "1" > /sys/class/gpio/gpio$BOOT/value
  echo "X728 Shutting down..."
  while [ 1 ]; do
    shutdownSignal=$(cat /sys/class/gpio/gpio$SHUTDOWN/value)
    if [ $shutdownSignal = 0 ]; then
      /bin/sleep 0.2
    else  
      pulseStart=$(date +%s%N | cut -b1-13)
      while [ $shutdownSignal = 1 ]; do
        /bin/sleep 0.02
        if [ $(($(date +%s%N | cut -b1-13)-$pulseStart)) -gt $REBOOTPULSEMAXIMUM ]; then
          echo "X728 Shutting down", SHUTDOWN, ", halting Rpi ..."
          sudo poweroff
          exit
        fi
        shutdownSignal=$(cat /sys/class/gpio/gpio$SHUTDOWN/value)
      done
      if [ $(($(date +%s%N | cut -b1-13)-$pulseStart)) -gt $REBOOTPULSEMINIMUM ]; then 
        echo "X728 Rebooting", SHUTDOWN, ", recycling Rpi ..."
        sudo reboot
        exit
      fi
    fi
  done' > /etc/x728pwr.sh
  sudo chmod +x /etc/x728pwr.sh
  sudo sed -i '$ i /etc/x728pwr.sh &' /etc/rc.local 

  
  #X728 full shutdown through Software
  #!/bin/bash

      sudo sed -e '/button/ s/^#*/#/' -i /etc/rc.local

      echo '#!/bin/bash
  BUTTON=13
  echo "$BUTTON" > /sys/class/gpio/export;
  echo "out" > /sys/class/gpio/gpio$BUTTON/direction
  echo "1" > /sys/class/gpio/gpio$BUTTON/value
  SLEEP=${1:-4}
  re='^[0-9\.]+$'
  if ! [[ $SLEEP =~ $re ]] ; then
     echo "error: sleep time not a number" >&2; exit 1
  fi
  echo "X728 Shutting down..."
  /bin/sleep $SLEEP
  #restore GPIO 13
  echo "0" > /sys/class/gpio/gpio$BUTTON/value
  ' > /usr/local/bin/x728softsd.sh
  sudo chmod +x /usr/local/bin/x728softsd.sh

   

  0 likes 0 likes Liked Like

  ---

  4
  Posts

  767
  Views

  Reply

  ---

• HH

  Harry Huang Staff member

  10/16/20, 6:39 PM

  @Aiden Ralph 

  Hi, Thanks

   

  The press time is related to the firmware of the MCU,  The purpose of pressing 3 seconds is to prevent accidental shutdown

  0 likes 0 likes Liked Like

  ---

• AS

  Annette Shepherd

  7/24/23, 12:25 PM

  Detaching the battery after shutdown requires a tweak that is specific to the hardware configuration and battery geometry dash lite attachment method of the X728 board.  The three-second button has an anti-shutdown safety feature.

  0 likes 0 likes Liked Like

  ---

• AN

  Adaut Nokolto

  9/22/23, 9:37 PM

  lease be cautious when modifying scripts related to power management, as improper changes can potentially lead to data corruption or other issues. Make sure to back up your data and configurations before proceeding.

  1. Identify the Button's GPIO Pin: Determine which GPIO pin the external button is connected to on the X728 board. This information should be available in the product documentation or on the board itself.

  2. Create or Modify a Shutdown Script:

     • You can create a custom script to handle the shutdown and power-off sequence. Here's a basic example using Python:
       python

        

       #!/usr/bin/env python import RPi.GPIO as GPIO import os import time # Set the GPIO pin for the external button button_pin = 18 # Replace with the actual GPIO pin GPIO.setmode(GPIO.BCM) GPIO.setup(button_pin, GPIO.IN, pull_up_down=GPIO.PUD_UP) try: while True: input_state = GPIO.input(button_pin) if input_state == False: # Button is pressed os.system("sudo poweroff") time.sleep(5) # Wait for the shutdown to complete os.system("sudo systemctl poweroff -i") time.sleep(0.2) except KeyboardInterrupt: pass finally: GPIO.cleanup()
       Save this script to a file (e.g., shutdown_button.py) and make it executable using chmod +x shutdown_button.py.

  You can also check mac show hidden folders option for mac os users, the best option.

  0 likes 0 likes Liked Like

  ---