@Aiden Ralph  Hi, It's hard for me to understand why you have this need; For a UPS or power expansion board, we need to consider the accidental factor of touching the switch manually. If th...

I have the X708 board and I want to modify the shutdown script. What I would like to do is do a full power off with 1 press of the external switch instead of pressing it for 8 seconds. Anyone know...

Hi, It appears that your fan is not working; we recommend that you do not put the case in until you have made sure the fan is working properly. We think you should have installed the fan script, ...

Hi, I have bought a Geekworm NASPi V2.0 2.5" SATA HDD/SSD Kit. I installed it with a Raspberry pi 4B 2GB and a fanxiang S101 2To SSD. I then installed OpenMediaVault v6 software. Everything works...

Hello， Please backup your data before setup and switch, otherwise you maybe lost your data.1. Inert HDDs to X885 shield and fix it.2. Please connect the X885 to your PC or Raspberry Pi board and k...

Hello, I recently bought a X885 and I am trying to use 2 drives in RAID 0. The product description and the wiki (https://geekworm.com/products/x885) both mention that the board has a RAID controll...

Hi,Philip Sorry, we haven't tested that. We cannot guarantee that the ice tower fan will work with it. Best regards Lisa

Hi, I'm planning to vertically mount a Raspberry (in a Racknex 5x 10" Rack mount). Would this also work with the standard ICE Tower or would I have to worry about worse heat transfer or even damag...

Hello， Realy sorry for the inconvenience. Could you please  try soldering it?  Thanks for your feedback, we will check the current stock product and improve it. And we have sent you a ...

Hello, I was assembling my NasPi Gemini 3.5" and the piece on the X885 where the 12V power jack is connected came off.   It appears to have been glued to the board. I cannot manage to make i...

Hello， Maybe you can contact the chip manufacturer for some advice. this their website https://www.jmicron.com/contact Best regards

I was trying to monitor s.m.a.r.t. values - especially temperature - of the HDD drives (Seagate 5TB) in Gemini 2.5 V2. There's a great piece of software called smartmontools, that can do that.When ...

@Harry Huang  I said PiKVM-A4 kit that is used for rpi-zero 2w. It means I used v2-hdmi-zero2w-lastest.img.xz.

Thanks for your valuable post;Need to ask you, which OS do you use?

1. Edit /boot/config.txt and add below codes. dtparam=i2c1=on dtparam=i2c_arm=on 2.  Edit /etc/modules-load.d/raspberrypi.conf and add below code. i2c-dev 3. install package pacman -S i2...

Purchased DACPI with power supply 5V/4A, assembled with Raspberry PI 4 and installed Volumio. Everything works as expected, except very annoying noise in pauses of music. This noise completely disa...

I noticed on a new install, I was having several errors in the system log every 5 seconds related to kvmd-watchdog.  I used the v3 Hat version of PiKVM on the A8 PCIe product.  It appears...

@Snuupy Snup Hi， The I2S Audio in（10pin SH1.0 connector） of X630-A3 is for I2S HDMI audio support. But you need a I2S cable.

Hi, official audio support is added. Is this working on Geekworm A3? Can you add instructions for how to connect I2S to X630? https://docs.pikvm.org/audio/

@Jose Legido Martínez Hi，The x728 supports the connection of a 4pin momentary switch, but the safe shutdown function requires an installation script to be realized. Please refer to here for...