I recently purchased a X825, X735 and X825-C2 case with momentary power switch. I am confused how to set the jumpers, which jumps should be connected on both the X825 and X735 boards? &...
All Posts
-
x708 software power shutdown
Hi I need this solution for my car, also. But i have a X728.Script seems to works ok, but if i study the behavior on shutdown, the X728 shuts down BEFORE the PI. That is no good. Running Buster, ...
-
X728 and Rpi4 - IOError: [Errno 121] Remote I/O error
@li xia Yes, as i mentioned in first post. I followed the guide on two Rpi4s. Only the Rpi3 worked.
-
Power off X728 after Pi4 was shut down from software
@li xia hello Could you tell what the GPIO5, GPIO12 and GPIO13 are used for? Thanks you.
-
Power off X728 after Pi4 was shut down from software
I want to put the X728 into the same state as "Force shutdown (Press and hold for >8 seconds)" but after the Pi4 was powered off from software. How can I power off the X728 board after the Pi4 ...
-
X728 Pi4 RTC not working
Apparenly on a freshly installed Ubuntu it works. Interesting...
-
X728 Pi4 RTC not working
Tested on Raspberry OS lite. Seems to work. sudo hwclock -v hwclock from util-linux 2.33.1 System Time: 1608307733.168204 Trying to open: /dev/rtc0 Using the rtc interface to the clock...
-
X728 Pi4 RTC not working
I purchased the X728 ups hat to be used with a Pi 4. I am having issues with RTC. I'm running Ubuntu Server 20.04. To rule out issues as my fault, here is what I did: - in /b...
-
X728 and Rpi4 - IOError: [Errno 121] Remote I/O error
Hi Running:PRETTY_NAME="Raspbian GNU/Linux 10 (buster)" Fresh hardware install, following GUIDE from https://raspberrypiwiki.com/X728-Software Jumpers: PLD Step: 6 outputs: pi@raspberrypi:~ $ ...
-
New X832 and X735 setup issues
I think I answered my own question in my OP, but I just realized while I was troubleshooting on my own, that the power supply I purchased is only 5V (actually indicates it can supply up to 8V on th...
-
New X832 and X735 setup issues
I'm new to using geekworm products, but decided to try out an X832 (single 3.5" HDD board) with X735 (power management board) with a raspberry pi 4 (4GB model), inside of the geekworm case. I also ...
-
usb 1-1.3: reset high-speed USB device number 4 using xhci_hcd
Hi, I have a Rpi 4 8G with an x708 UPS and X828 SDD/HDD boardes attached and alos using a geekwork 5v 4a power supply and I'm seeing the below errors on the raspberry pi OS syslog, I'm conce...
-
X825 HAT with other single board computers
@li xia but is it using some feature or concept unique to Raspberry Pi? According to description it is only setting up a link through USB 3.0, emulating standard USB drive, and the relationship wi...
-
X825 HAT with other single board computers
As I can see, the only difference between Jetson Nano and RPi NAS HATs is the shape, sharing same electronics. And hardware need is only a functional USB3.x Port. Can I so suppose that appart of t...
-
Can i use ups hat x735 with raspberry pi tv hat?
Good morning. As per object I would like to know if it is possible to stack the raspberry pi 4 + x735 v2.1 + Raspberry Pi TV HAT. I would like to build an htpc that can be turned off comfortably wi...
-
Does X829 support mdadm raid=1?
@li xia That does not answer my question. The question is simple. Can you confirm whether or not I will be able to set up a 2 drive raid=1 array if my drieves are connected to my RPi4 through the X...
-
Does X829 support mdadm raid=1?
Well the title pretty much says it all. I am wondering if the X829 will support a two drive raid 1 array?
-
NAS Media Server for family
I'm pretty new to all of this but I want to make a NAS server for my family. Ideally, what I want is for each person to have their own drive (5 in total) for their personal use (mainly to str...
-
x725 CHG LED Status
Hi, Unless there is something else going on that I misunderstand, this is not my issue. I am having an issue with the batteries not staying charged even when plugged in with a more than capable po...
-
x725 CHG LED Status
@li xia That is what I expected the Blink Status to mean, However I wanted to verify. Thank you. As for the issue that I am seeing, I ran a few tests and have a bit of further information o...