
Have a question?
Notified by email when this product becomes available
- Description
- Manual
- Shipping Policy
- Reviews
Overview
The ESP32-C6-Touch-LCD-1.47 is a microcontroller development board based on the ESP32-C6FH8, supporting 2.4GHz Wi-Fi 6 and Bluetooth BLE 5. It integrates 8MB Flash and an onboard 1.47inch capacitive touch LCD (172 × 320 Resolution, 262K Display colors), capable of smoothly running GUI programs such as LVGL.
Combined with the onboard 6-axis IMU, TF card slot, battery charging circuit and rich peripheral interfaces, it enables rapid development of HMI, IoT nodes and other low-power wireless applications for the ESP32-C6.
Key Features
⚡ ESP32-C6FH8 Dual-Core RISC-V
- High-Performance Processor: RISC-V 32-bit, up to 160MHz.
- Low-Power Processor: Second RISC-V 32-bit core up to 20MHz, with flexible clock, multiple power modes and precise control for low-power scenarios.
- Rich Onboard Memory: 320KB ROM, 512KB HP SRAM, 16KB LP SRAM and 8MB Flash.
📶 Wi-Fi 6 + Bluetooth 5 (BLE)
- Dual Wireless Protocols: 2.4GHz Wi-Fi 6 (802.11 ax/b/g/n) and Bluetooth 5 (BLE), with an onboard ceramic antenna.
- IoT-Ready: Ideal for wireless sensor nodes, smart-home endpoints and cloud-connected HMI devices.
🖥️ 1.47inch Capacitive Touch LCD
- 172 × 320 IPS Display: 262K colors, driven by the JD9853 controller over 4-wire SPI.
- Capacitive Touch: AXS5106L touch controller via I2C, supporting smooth LVGL-based GUI programs.
🎛️ Rich Onboard Peripherals
- QMI8658A 6-Axis IMU: 3-axis accelerometer + 3-axis gyroscope (shared I2C bus).
- TF Card Slot: SPI interface for storing images or files.
- Battery Power Management: ETA6098 charging circuit with VBAT pin for battery-powered projects.
- USB Type-C: Full-speed USB for power supply, programming and USB communication.
- 22Pin Header: Breaks out power, BAT, USB, UART, I2C, ADC and most GPIOs.
🛠️ Flexible Development
- Arduino IDE: Gentle learning curve, huge community and library ecosystem — ideal for beginners and rapid prototyping.
- ESP-IDF: Espressif official professional framework with fine-grained control, supporting command line and VS Code (Espressif IDF plugin) workflows.
Compatibility & Applications
- Frameworks: Arduino IDE, ESP-IDF (VS Code / command line)
- HMI & GUI: LVGL-based touch interfaces for embedded control panels
- IoT Nodes: Wi-Fi 6 / BLE sensor nodes, smart-home endpoints and wireless data loggers
- Portable Devices: Battery-powered handheld instruments and wearables (via ETA6098 charging circuit)
- Data Logging: TF card storage projects combining sensor sampling (IMU) with local file storage
Usage Precautions
⚠️ IMPORTANT NOTES:
- Battery Safety: Verify battery polarity and type before connecting. Connect the battery positive terminal to VBAT and negative to GND — do not connect VBAT to 3V3 or USB VBUS.
- GPIO8 (BOOT): Boot-mode control pin. If your program occupies it and blocks re-programming, temporarily connect GPIO8 to 3V3 and re-enter download mode.
- GPIO12 / GPIO13: USB D-/D+. Do not use them as general-purpose GPIO when USB functionality is required.
- GPIO1 / GPIO2 (Shared SPI): Shared clock/data lines between the LCD and TF card. Control each device’s chip select properly; keep inactive devices deselected, and format TF cards as FAT32.
- GPIO18 / GPIO19 (Shared I2C): Already connected to the touch controller and IMU. Mind I2C address conflicts, pull-ups and bus voltage levels when adding external I2C devices.
- GPIO0: Connected to the battery voltage sampling circuit (voltage divider). Consider its impact when reusing as a general-purpose ADC/GPIO.
- GPIO5 / GPIO6: Connected to QMI8658A IMU interrupt outputs. Configure IMU interrupts accordingly when reusing these pins.
Note: Warranty service is not available for product damage resulting from failure to follow the guidelines above.
Technical Specifications
| Feature | Specification |
|---|---|
| Main Controller | ESP32-C6FH8, dual RISC-V 32-bit processors (up to 160MHz + up to 20MHz) |
| Wireless | 2.4GHz Wi-Fi 6 (802.11 ax/b/g/n), Bluetooth 5 (BLE), onboard antenna |
| Memory | 320KB ROM, 512KB HP SRAM, 16KB LP SRAM, 8MB Flash |
| Display | 1.47inch IPS LCD, 172 × 320 resolution, 262K colors, JD9853 driver (4-wire SPI) |
| Touch | Capacitive touch, AXS5106L controller (I2C) |
| IMU | QMI8658A 6-axis (3-axis accelerometer + 3-axis gyroscope) |
| Storage Expansion | TF card slot (SPI interface, for images or files) |
| Battery / Power Management | ETA6098 charging & power management, 3.3V regulated supply (ME6217C33M5G), battery voltage ADC sampling |
| USB | USB Type-C, full-speed (power, programming and USB communication) |
| GPIO Breakout | 22Pin header: power, BAT, USB, UART, I2C, ADC and multiple GPIOs |
| Buttons | RESET button, BOOT button (GPIO8) |
| Development Environment | Arduino IDE, ESP-IDF |
Packing List
- 1 x ESP32-C6-Touch-LCD-1.47 Development Board with 2 headers (not soldered)
- Note: TF card, battery and other peripherals shown in the product images are not included.
Refer to: https://wiki.geekworm.com/ESP32-C6-Touch-LCD-1.47
Please email to us at info@geekworm.com if you have other questions.
We send orders to worldwide with tracking number.
For detail refer to Shipping Policy
